Interior wall panel guide

Planning Fluted Wall Panels Around Doors, Corners and Sockets

Before ordering or fitting fluted wall panels, mark where grooves, cuts and joints will fall and how the panels will meet doors, corners, sockets, the ceiling and the floor. Use the actual panel dimensions and check the wall condition.

  1. 1. Choose panel
  2. 2. Mark fixed features
  3. 3. Agree profile layout
  4. 4. Confirm fitting scope
View the approval checklist
Enoch feature wall with light wood fluted sides and an ivory marble-look centre
Our light wood side panels frame the ivory centre and define the focal area.

Panel selection

Which panel dimensions control the visible pattern?

The profile width, effective installed coverage and groove shape determine how the pattern repeats. The available panel length determines whether a run can reach from floor to ceiling or needs a horizontal joint.

A room photo can show how the grooves look in the light. For the layout, confirm the usable width each fitted panel adds and the available length of the exact product you plan to order.

001 Light Wood - Classic

Light wood grain with a pronounced fluted profile.

Our reference profile measures 160 mm wide and 23 mm thick. Confirm the effective installed coverage separately, along with the available length and proposed joints and edges.

001 Light Wood Classic fluted wall panel product image

A223 Beigi - Modern

Soft beige with understated fluted detailing.

Confirm the supplied profile and fitting requirements with us before planning how it will meet corners, sockets or exposed edges.

A223 Beigi Modern fluted wall panel product image

Groove alignment

Where should the first full profile and the final cut fall?

Plan the focal area and both ends of the wall together so a narrow cut does not land beside the TV, doorway or main viewing position by accident.

Mark the centreline or the area that should draw the eye, then check what the selected profile leaves at each end. The profile and wall determine the starting point. If you change profiles, recheck the end widths and visible joints. In our profile close-up, the raised faces and recessed grooves are easy to distinguish. Check where each visible edge falls across that shape.

  1. Left finish
  2. Focal area
  3. Right finish

Check the width and groove position at both cut ends.

Close-up of raised faces and recessed grooves across fluted panel samples

Fixed fittings

How should sockets, switches and a TV position affect the layout?

Mark electrical faceplates, the TV position and bracket, and adjacent cabinetry on the wall plan before finalising groove positions. A socket or wall switch cut-out that crosses a groove or panel joint can interrupt the pattern and affect how the faceplate meets the finished surface.

Agree how the faceplates should meet the finished wall. If a socket or switch needs relocation or extension, agree that as a separate scope with a qualified electrical provider.

Ivory marble and light wood TV feature wall

In our TV-wall example, 001 Light Wood fluted panels sit on either side of an ivory marble-look UV centre. Use the video to see how the side panels frame the centre, then mark your TV and power-point positions against the actual wall dimensions before choosing the panel layout.

Edge details

What changes at doors, corners and exposed ends?

A door reveal, an outside corner and a panel ending on a painted wall each need a different edge decision. Agree how each edge should look and confirm the detail suits the selected profile before fitting. With our A223 and 001 panels, discuss those details against the specific profile you plan to use.

Door frame

The panel adds depth next to the frame or reveal. Where should the fluting stop, and will the finished edge leave enough clearance for the door?

Return corner

The profile meets a change in wall direction. Should the fluting stop at the corner or continue onto the adjoining wall, and how will the profile meet that corner?

Exposed end

The panel edge stays visible where the fluting stops on a painted wall. Which compatible finish will give that transition the intended appearance?

Wall condition

When is the existing wall ready for a panel finish?

The wall is ready when it is sound and meets the fitting requirements of the selected panel. Address active damp or loose material before covering the wall.

Check flatness, signs of moisture and the condition of existing finishes. Check how far the finished surface will project and what that means for door clearance, skirting and electrical faceplates.

Before you order

What should be agreed before materials are ordered or fitting begins?

Agree the exact panel and dimensions, profile direction and start point, positions of openings and power points, joint and edge treatment, and who handles preparation or electrical work.

  • Panel and wall: Confirm product code, finish, available length, effective installed coverage, and wall width and height.
  • Pattern: Mark groove direction, the starting point and both end cuts.
  • Openings and fittings: Mark door frames, cabinets, sockets, switches, TV and bracket.
  • Joints and edges: Agree where joins may be visible and how corners, exposed ends, the ceiling and skirting or floor will meet the panel.
  • Responsibilities: Confirm who provides the panels, handles fitting and wall preparation, and arranges any electrical work.

We can help you confirm the shortlisted panel and discuss supply and the proposed fitting scope for your project location in West Malaysia.

Fluted wall panel layout FAQs

Yes. Mark where the fluted area starts and stops, then agree how each exposed edge will meet the adjacent finish.

The 160 mm figure is our reference profile width. Confirm the effective installed width before setting out the groove pattern or ordering panels.

It may be able to stay if its position and faceplate can work with the finished panel surface. Ask a qualified electrical provider to assess any extension or relocation.

Compare the available panel length with the height of each uninterrupted run. If a join is needed, agree where it will be visible before ordering.

Light travelling across the wall can emphasise grooves and surface transitions. View the panel under similar lighting and check likely joint positions from your normal viewing angle.

Discuss your fluted-wall layout

In summary, confirm the profile and agree where visible cuts, joints and edges will fall before you order.

Send us a straight-on wall photo or plan with approximate width and height, marked door, socket and TV positions, your preferred Enoch panel and your project location so we can discuss the product details and whether installation is available for your job.

Discuss your fluted-wall layout
Topics